
18.5V 5Ah 21700 Lithium-Ion Battery Pack
Model: KX-LIION18.5/5-92.5Wh/21700
A 5S1P pack with 92.5Wh nominal energy in a 22 × 110 × 79mm maximum envelope. Send the load profile and charger specification so we can confirm current limits and cutoff for your device.
View specifications · Compare configurations
Review my 5S charger and load on WhatsApp
Product appearance rendering. Confirm the final assembly and connector layout on the approved drawing.
Ask about this product on WhatsAppProduct details
Configuration and application fit
Consider this configuration for OEM equipment designed around a 5-series lithium-ion pack. Check the complete input-voltage window, startup current and battery compartment before selecting it.
Technical specifications
| Koxin model | KX-LIION18.5/5-92.5Wh/21700 |
|---|---|
| Chemistry | Lithium-ion |
| Cell format / configuration | 21700 / 5S1P |
| Nominal voltage | 18.5V |
| Rated / minimum capacity | 5000mAh / 5000mAh at 0.2C, 25°C |
| Typical capacity | 5050mAh at 0.2C, 25°C |
| Nominal energy | 92.5Wh (18.5V × 5Ah; calculated) |
| Maximum pack envelope | 22 × 110 × 79mm (thickness × width × height) |
| Lead length | 100 ± 5mm |
| Pack weight | Approximately 380g |
| Pack AC impedance | ≤80mΩ at 1kHz |
| Charge voltage | 21V, CC/CV |
| Recommended charge current | Confirm for the approved configuration |
| Discharge current / cutoff | Confirm the operating current, pulse duration and cutoff before ordering |
| Protection | 5S protection board; thresholds to be confirmed |
| Wiring / connector | Three AWG16 wires; connector mating specification available for review |
These values apply to the configuration described here. Changes to cells, protection electronics, wiring or packaging require an updated specification and sample approval.
Mechanical and electrical integration
The third wire must be identified on the approved wiring drawing. Do not assume it is a temperature or communication lead. Charging current, low-voltage cutoff and temperature limits require confirmation for this configuration.
Request the dimensioned drawing, connector mating details and approved pinout before finalizing your housing or harness. The image shows the reference appearance of this configuration.
OEM customization and sample approval
Tell Koxin which dimensions, capacity, connector, lead length, protection functions and labeling your project requires. Custom changes are assessed individually; a different voltage, chemistry or current rating requires engineering review.
- Share your application, electrical requirements and available installation space.
- Agree on a proposed configuration, drawing, sample quantity and quotation.
- Evaluate samples in your device, including startup load, charging, temperature and protection recovery.
- Approve the final specification and inspection requirements before production.
Development charges depend on structural design, protection circuitry and enclosure work. Some projects may qualify for a reduction or waiver after an agreed order volume.
Documents and validation
Request a model-specific specification, mechanical drawing, wiring information and the available testing or transport documents for your destination. Cycle-life targets must include temperature, charge/discharge rate, cutoff and capacity-retention criteria. A specification target is not a substitute for a test report.
For repeat production or assembly outsourcing, include cell sourcing requirements, approved substitutions, incoming inspection criteria and change-control expectations in your RFQ.
Frequently asked questions
Can this pack replace any 18V battery?
No. Match the charger, full operating-voltage window, connector, polarity, protection behavior and current demand. Nominal voltage alone does not establish compatibility.
Is 92.5Wh the usable energy in my device?
It is nominal voltage multiplied by rated capacity. Usable energy depends on load, temperature, cutoff and conversion losses.
What are the MOQ, sample cost and lead time?
Samples and small-batch trials are supported. MOQ depends on capacity, configuration and project requirements. Samples are charged; a refund or production-order credit may be agreed based on order value or quantity. Samples can be completed in as little as 7 working days, depending on complexity and available materials. Production generally takes 15–25 days; the exact schedule and starting milestone are confirmed with the order.
Is this battery certified for my target market?
Certification and transport documentation must be checked against the exact battery configuration and destination. Ask for available model-specific reports and test summaries. Koxin can assist with test samples and coordination; test and certification costs depend on the laboratory quotation and project scope.
Request a configuration review
Send application, voltage and capacity, maximum dimensions or a drawing, continuous and peak current with pulse duration, charging method and current, protection requirements, sample and production quantities, target market and delivery timing.
Request a quote on WhatsApp · Use the inquiry form below — WhatsApp
Prepare your requirements with our battery pack RFQ checklist and BMS selection guide.
Compare related configurations
Need a different configuration?
Share your application, required quantity and operating conditions. Include any dimensions, current limits, communication requirements or documents needed for evaluation.
Discuss a configuration on WhatsApp Technical document requests
Send an inquiry
Start a conversation on WhatsApp. Your message will include the product or page you are viewing.
Discuss your requirements on WhatsApp