warren@koxinenergy.com WhatsApp

7.2V 4.4Ah 18650 Lithium-Ion Battery Pack

Model: KX-NMC7.2/4.4-31.68Wh/18650

This 2S2P pack is specified for low-current equipment with operating discharge up to 0.2A. Share startup peaks as well as average load. The center connector position is unused.

View specifications · Compare configurations

Check my device startup load on WhatsApp

Product appearance rendering. Confirm the final assembly and connector layout on the approved drawing.

Ask about this product on WhatsApp

Product details

Configuration and application fit

This configuration is a candidate for low-current OEM electronics. The stated 0.2A discharge limit is a key selection constraint; do not infer motor, tool or drone suitability from capacity or the 18650 cell format.

Check this configuration on WhatsApp

Technical specifications

Koxin model KX-NMC7.2/4.4-31.68Wh/18650
Chemistry NMC lithium-ion
Cell format / configuration 18650 / 2S2P
Nominal voltage 7.2V
Rated / minimum capacity 4.4Ah / 4.1Ah at C5
Nominal energy Approximately 31.68Wh
Pack dimensions 76 ± 2 × 70 ± 2 × 20 ± 1mm
Weight 185 ± 20g
Packaging PVC wrap
Internal resistance ≤91mΩ
Charge voltage 8.3–8.4V
Charge current ≤0.88A
Charge termination current 44–88mA
Operating discharge current ≤0.2A as specified; confirm suitability for the actual load
Discharge cutoff Approximately 5.6V
Protection Overcharge, overdischarge, temperature protection and balancing
Connector / leads JST-SM-3P, center position unused; 100 ± 10mm leads
Polarity Red positive, black negative
Operating temperature Charge: 5 to 45°C; discharge: -20 to 55°C

These values apply to the configuration described here. Changes to cells, protection electronics, wiring or packaging require an updated specification and sample approval.

Mechanical and electrical integration

The connector has three positions but the center position is unused. It is not evidence of an external NTC or communication signal. Send the device startup and operating currents before confirming samples.

Request the dimensioned drawing, connector mating details and approved pinout before finalizing your housing or harness. The image shows the reference appearance of this configuration.

OEM customization and sample approval

Tell Koxin which dimensions, capacity, connector, lead length, protection functions and labeling your project requires. Custom changes are assessed individually; a different voltage, chemistry or current rating requires engineering review.

  1. Share your application, electrical requirements and available installation space.
  2. Agree on a proposed configuration, drawing, sample quantity and quotation.
  3. Evaluate samples in your device, including startup load, charging, temperature and protection recovery.
  4. Approve the final specification and inspection requirements before production.

Development charges depend on structural design, protection circuitry and enclosure work. Some projects may qualify for a reduction or waiver after an agreed order volume.

Documents and validation

Request a model-specific specification, mechanical drawing, wiring information and the available testing or transport documents for your destination. Cycle-life targets must include temperature, charge/discharge rate, cutoff and capacity-retention criteria. A specification target is not a substitute for a test report.

For repeat production or assembly outsourcing, include cell sourcing requirements, approved substitutions, incoming inspection criteria and change-control expectations in your RFQ.

Frequently asked questions

Does 4.4Ah mean this battery can deliver 4.4A?

No. Capacity and current limit are different specifications. The supplied configuration lists discharge current up to 0.2A, which must be checked against your device.

Can I use a three-wire communication harness?

The specified center connector position is unused. Any communication or temperature-signal requirement needs a different, reviewed wiring configuration.

What are the MOQ, sample cost and lead time?

Samples and small-batch trials are supported. MOQ depends on capacity, configuration and project requirements. Samples are charged; a refund or production-order credit may be agreed based on order value or quantity. Samples can be completed in as little as 7 working days, depending on complexity and available materials. Production generally takes 15–25 days; the exact schedule and starting milestone are confirmed with the order.

Is this battery certified for my target market?

Certification and transport documentation must be checked against the exact battery configuration and destination. Ask for available model-specific reports and test summaries. Koxin can assist with test samples and coordination; test and certification costs depend on the laboratory quotation and project scope.

Request a configuration review

Send application, voltage and capacity, maximum dimensions or a drawing, continuous and peak current with pulse duration, charging method and current, protection requirements, sample and production quantities, target market and delivery timing.

Request a quote on WhatsApp · Use the inquiry form below — WhatsApp

Prepare your requirements with our battery pack RFQ checklist and BMS selection guide.

Compare related configurations

Need a different configuration?

Share your application, required quantity and operating conditions. Include any dimensions, current limits, communication requirements or documents needed for evaluation.

Discuss a configuration on WhatsApp Technical document requests

Send an inquiry

Start a conversation on WhatsApp. Your message will include the product or page you are viewing.

Discuss your requirements on WhatsApp
Prefer email? Send a detailed inquiry

Product: 7.2V 4.4Ah 18650 Lithium-Ion Battery Pack

Chat on WhatsApp