
3.7V 1050mAh LiPo Battery with NTC
Model: KX-LIPO3.7/1.05-3.885Wh/902248
A three-wire LiPo pack with a temperature-sensing lead. The 3.15A limit is a cell rating. Request the finished-pack current rating and dimensioned drawing before finalizing your enclosure.
View specifications · Compare configurations
Request the pack drawing and load review on WhatsApp
Product appearance rendering. Confirm the final assembly and connector layout on the approved drawing.
Ask about this product on WhatsAppProduct details
Configuration and application fit
Consider this configuration for compact OEM electronics that need a temperature-sensing lead. Validate assembled-pack discharge capability and mechanical clearance before committing to an enclosure or a 3C load.
Technical specifications
| Koxin model | KX-LIPO3.7/1.05-3.885Wh/902248 |
|---|---|
| Chemistry / configuration | Lithium-ion polymer / single cell |
| Nominal voltage | 3.7V |
| Rated / minimum capacity | 1050mAh / 1050mAh at 0.2C |
| Typical capacity | 1080mAh at 0.2C |
| Nominal energy | 3.885Wh (3.7V × 1.05Ah; calculated) |
| Finished pack envelope | Confirm the approved mechanical drawing before enclosure design |
| Standard charge current | 210mA (0.2C) |
| Fast charge current | 1050mA (1C), subject to temperature limits |
| Charge voltage | 4.2V, CC/CV |
| Standard discharge current | 210mA (0.2C) |
| Cell maximum discharge current | 3150mA (3C); assembled-pack rating to be confirmed |
| Normal discharge cutoff | 3.0V |
| Charging temperature / current | 0–10°C: maximum 0.2C; 10–45°C: maximum 1C |
| Discharging temperature | -20 to 60°C |
| Connector / leads | PHR-3; three UL1571 24AWG wires, 50 ± 3mm |
| NTC | 10kΩ ± 1%; B value and pin assignment to be confirmed |
| Protection | Overcharge, overdischarge, overcurrent and short-circuit protection |
These values apply to the configuration described here. Changes to cells, protection electronics, wiring or packaging require an updated specification and sample approval.
Mechanical and electrical integration
The 3C figure is listed in the cell-performance section and is not treated here as an independently validated assembled-pack rating. Obtain a confirmed pack drawing, lead color/pin map and temperature-sensor curve before integration.
Request the dimensioned drawing, connector mating details and approved pinout before finalizing your housing or harness. The image shows the reference appearance of this configuration.
OEM customization and sample approval
Tell Koxin which dimensions, capacity, connector, lead length, protection functions and labeling your project requires. Custom changes are assessed individually; a different voltage, chemistry or current rating requires engineering review.
- Share your application, electrical requirements and available installation space.
- Agree on a proposed configuration, drawing, sample quantity and quotation.
- Evaluate samples in your device, including startup load, charging, temperature and protection recovery.
- Approve the final specification and inspection requirements before production.
Development charges depend on structural design, protection circuitry and enclosure work. Some projects may qualify for a reduction or waiver after an agreed order volume.
Documents and validation
Request a model-specific specification, mechanical drawing, wiring information and the available testing or transport documents for your destination. Cycle-life targets must include temperature, charge/discharge rate, cutoff and capacity-retention criteria. A specification target is not a substitute for a test report.
For repeat production or assembly outsourcing, include cell sourcing requirements, approved substitutions, incoming inspection criteria and change-control expectations in your RFQ.
Frequently asked questions
Is the maximum 3C current guaranteed for the complete pack?
The cell specification lists 3.15A. The assembled battery, protection board, wiring and connector must be validated together for the required load and duty cycle.
Can I fast-charge across the full temperature range?
No. The specification limits charging to 0.2C from 0 to 10°C and up to 1C from 10 to 45°C. The host must use a compatible charging and temperature-control design.
What are the MOQ, sample cost and lead time?
Samples and small-batch trials are supported. MOQ depends on capacity, configuration and project requirements. Samples are charged; a refund or production-order credit may be agreed based on order value or quantity. Samples can be completed in as little as 7 working days, depending on complexity and available materials. Production generally takes 15–25 days; the exact schedule and starting milestone are confirmed with the order.
Is this battery certified for my target market?
Certification and transport documentation must be checked against the exact battery configuration and destination. Ask for available model-specific reports and test summaries. Koxin can assist with test samples and coordination; test and certification costs depend on the laboratory quotation and project scope.
Request a configuration review
Send application, voltage and capacity, maximum dimensions or a drawing, continuous and peak current with pulse duration, charging method and current, protection requirements, sample and production quantities, target market and delivery timing.
Request a quote on WhatsApp · Use the inquiry form below — WhatsApp
Prepare your requirements with our battery pack RFQ checklist and BMS selection guide.
Compare related configurations
Need a different configuration?
Share your application, required quantity and operating conditions. Include any dimensions, current limits, communication requirements or documents needed for evaluation.
Discuss a configuration on WhatsApp Technical document requests
Send an inquiry
Start a conversation on WhatsApp. Your message will include the product or page you are viewing.
Discuss your requirements on WhatsApp