warren@koxinenergy.com WhatsApp

3.7V 1200mAh LiPo Battery with Protection Board

Model: KX-LIPO3.7/1.2-4.44Wh/103040

A protected two-wire LiPo pack with a maximum initial envelope of 10 × 30.5 × 42.5mm. Allow for thickness change and lead routing. A mating connector must be specified separately.

View specifications · Compare configurations

Review my enclosure and lead requirements on WhatsApp

Product appearance rendering. Confirm the final assembly and connector layout on the approved drawing.

Ask about this product on WhatsApp

Product details

Configuration and application fit

Evaluate it for compact low-power electronics where a two-wire lithium-polymer configuration fits the design. Check the complete finished-pack dimensions, rather than assuming the former cell model number describes the assembled size.

Check this configuration on WhatsApp

Technical specifications

Koxin model KX-LIPO3.7/1.2-4.44Wh/103040
Chemistry / configuration Lithium-ion polymer / single cell
Nominal voltage 3.7V
Rated / minimum capacity 1200mAh / 1200mAh at 0.2C
Typical capacity 1230mAh at 0.2C
Nominal energy 4.44Wh (3.7V × 1.2Ah; calculated)
Finished pack dimensions 10 × 30.5 × 42.5mm maximum initial thickness × width × height
Thickness allowance Specification lists 10.2mm after 300 cycles; confirm design clearance
Pack impedance ≤180mΩ
Standard charge current 240mA (0.2C)
Fast charge current 1200mA (1C)
Charge voltage 4.2V, CC/CV
Standard discharge current 240mA (0.2C)
Cell maximum discharge current 1200mA (1C); confirm the finished assembly for your load
Normal discharge cutoff 2.75V
Temperature range Charge: 10 to 45°C; discharge: -10 to 60°C
Lead arrangement Two UL1007 26AWG wires, 50 ± 5mm; no connector specified
Protection Overcharge, overdischarge, overcurrent and short-circuit protection

These values apply to the configuration described here. Changes to cells, protection electronics, wiring or packaging require an updated specification and sample approval.

Mechanical and electrical integration

Allow clearance for the protection board, lead exit and thickness change. The protection overcurrent threshold is a fault-response setting, not a normal operating-current rating. Confirm a connector and lead polarity on the production drawing if your assembly requires them.

Request the dimensioned drawing, connector mating details and approved pinout before finalizing your housing or harness. The image shows the reference appearance of this configuration.

OEM customization and sample approval

Tell Koxin which dimensions, capacity, connector, lead length, protection functions and labeling your project requires. Custom changes are assessed individually; a different voltage, chemistry or current rating requires engineering review.

  1. Share your application, electrical requirements and available installation space.
  2. Agree on a proposed configuration, drawing, sample quantity and quotation.
  3. Evaluate samples in your device, including startup load, charging, temperature and protection recovery.
  4. Approve the final specification and inspection requirements before production.

Development charges depend on structural design, protection circuitry and enclosure work. Some projects may qualify for a reduction or waiver after an agreed order volume.

Documents and validation

Request a model-specific specification, mechanical drawing, wiring information and the available testing or transport documents for your destination. Cycle-life targets must include temperature, charge/discharge rate, cutoff and capacity-retention criteria. A specification target is not a substitute for a test report.

For repeat production or assembly outsourcing, include cell sourcing requirements, approved substitutions, incoming inspection criteria and change-control expectations in your RFQ.

Frequently asked questions

Does this version include a temperature-sensing wire?

The reference assembly uses two wires and does not specify an external NTC lead. Ask for a reviewed three-wire version if the host charger needs a temperature signal.

Can you supply a different connector or lead length?

Send the mating connector, pin order, lead length and drawing. Koxin will assess the change and confirm the resulting dimensions, electrical limits, MOQ and quotation.

What are the MOQ, sample cost and lead time?

Samples and small-batch trials are supported. MOQ depends on capacity, configuration and project requirements. Samples are charged; a refund or production-order credit may be agreed based on order value or quantity. Samples can be completed in as little as 7 working days, depending on complexity and available materials. Production generally takes 15–25 days; the exact schedule and starting milestone are confirmed with the order.

Is this battery certified for my target market?

Certification and transport documentation must be checked against the exact battery configuration and destination. Ask for available model-specific reports and test summaries. Koxin can assist with test samples and coordination; test and certification costs depend on the laboratory quotation and project scope.

Request a configuration review

Send application, voltage and capacity, maximum dimensions or a drawing, continuous and peak current with pulse duration, charging method and current, protection requirements, sample and production quantities, target market and delivery timing.

Request a quote on WhatsApp · Use the inquiry form below — WhatsApp

Prepare your requirements with our battery pack RFQ checklist and BMS selection guide.

Compare related configurations

Need a different configuration?

Share your application, required quantity and operating conditions. Include any dimensions, current limits, communication requirements or documents needed for evaluation.

Discuss a configuration on WhatsApp Technical document requests

Send an inquiry

Start a conversation on WhatsApp. Your message will include the product or page you are viewing.

Discuss your requirements on WhatsApp
Prefer email? Send a detailed inquiry

Product: 3.7V 1200mAh LiPo Battery with Protection Board

Chat on WhatsApp